Posts Tagged ‘First Steps’

Initial Steps in Hard Drive Recovery

Wednesday, July 1st, 2009

Andrew Whitehead is a contributor at Free-backup.info — the home of the popular Amazon S3 based tool for online file backup — Back2zip. This article can be found at http://free-backup.info/initial-steps-in-hard-drive-recovery.html

First Steps in Hard Drive Recovery

If you find that your hard drive is no longer functioning, remember that a hard drive recovery is nearly always possible, so there is no need for panic. Data loss is not unusual and in nearly all cases the data can be recovered. Only in severe severe cases involving platter damage, magnetic degradation, or over-write of a file will the data be practically unrecoverable, and even in these cases a hard drive recovery by MFM photography may be possible if the data is valuable enough to justify huge expense.

Having said that, there are steps you can take to minimize further data loss and greatly increase your chances of successful hard drive recovery

Initial Steps in Hard Drive Recovery after a ‘crash’

If you find that you are unable to boot to the operating system, and you can no longer see the hard drive in the BIOS, there is a strong possibility that your hard drive has crashed. In this case you should shut the whole system down immediately. If there is some physical problem with the hard drive, it will be made a lot worse if you run power through the hard drive attempting to reboot the system.

If the head stack inside your drive is damaged, trying to run it will cause additional damage to the surfaces of the platters in your hard drive, and this is where the data you are wanting to recover is stored.

Initial Steps in Hard Drive Recovery after Corruption

If you have accidentally reformatted your hard drive, or accidentally deleted a file or folder, once again you must not write any new information onto your drive. The files you have deleted are still intact somewhere on the drive. Deleting a file simply means removing the location tag for that file, allowing that area of the drive to be over-written. If you add any new data it is possible that it will over-write your lost data effectively losing it forever.

If you believe a partition has become corrupted on your hard drive, it is very important not to try and re-install your operating system or add any new data to the drive.

If you have accidentally deleted a partition, attempting to restore it by formatting the drive will not recover your data, it will only result in the addition of an empty partition.

If you experience a single file corruption, any attempt to create a new file with the same name will partially over-write the file, greatly decreasing your chances of a full recovery.

This is just a short selection of the more common reasons for losing data from your hard drive, and illustrates that some attempts made by you, or even an IT technician, to recover a file or drive could decrease the chances of subsequent professional recovery efforts, or even make a successful recovery impossible. If you have any doubts about what action to take, just ask yourself this question: “Am I prepared to lose that data? “.

read the full article

File Recovery Using DOS Undelete

Friday, May 29th, 2009

Andrew Whitehead is a contributor at Free-backup.info — the home of the popular Amazon S3 based tool for online file backup — Back2zip. This article can be found at http://free-backup.info/file-recovery-using-dos-undelete.html

First Steps in DOS File Recovery

The first three steps in file recovery are quite easy and require no specific knowledge:-

1)Don’t panic! Your information is still there, and safe.

2)Don’t touch the keyboard! Your information is safe…until your operating system writes over it.

3)Don’t switch off! A lot of temporary files are created during start up, and you don’t want them to be created over the top of your accidentally deleted files.

File Recovery Levels in DOS

Later versions of DOS (DOS 5.* and onwards) have three possible levels of file recovery, Delete Sentry, Delete Tracker, and the basic Undelete.

Delete Sentry offers the highest degree of protection, and works in a similar fashion to Recycle Bin in that it keeps copies of all your deleted files in a hidden file. This protects them from being overwritten and more or less guarantees file recovery will be possible. The down side is that the file can end up being huge. In DOS 5 the maximum size is 7% of your hard drive capacity, in DOS 6 it can go to 20%!

Those values can be changed by fiddling with UNDELETE.INI but it is quite a tedious job, as is the purging routine to get rid of all those files permanently.

The next level of file recovery is Delete Tracking, which stores the location of deleted files in a file called PCTRACKR.DEL. This uses less disk space, but the price you pay is that the stored locations may be overwritten if you don’t act promptly, and then your files will be impossible to recover.

The third level of file recovery is the standard UNDELETE method. This is the one where DOS brings back a list of your deleted files, all with the first letter of their names replaced by #. It then asks you to supply the missing first letter. Fortunately it doesn’t matter if you can’t remember it, just type any letter at random and DOS will go ahead and tell you that your file has been successfully recovered, even if it does have some unpronounceable name.

Using DOS File Recovery

In theory, to use DOS file recovery all that is required is for you to type in ‘UNDELETE’ at the DOS prompt, but when you do don’t be too surprised if nothing happens or your efforts are rewarded by nothing more than a reply saying something like ‘38 files can be recovered’, but with none of the promised file recovery actually taking place.

If this happens, it is because you have those three levels of file recovery to choose from. The level of file recovery protection is configured by editing the AUTOEXEC.BAT file so only one level can be enabled at a time, and the UNDELETE command requires the relevant switch to run it.

Luckily this is not as horribly complex as it sounds; the UNDELETE switches are fairly simple. If you have the basic level enabled, just use UNDELETE with no switch. If you have specified Delete Tracker the switch is /DT, and logically enough for Delete Sentry it is /DS.

read the full article

Energy Smart Miami – Cisco Behind the Smart Grid

Thursday, May 21st, 2009

Despite the backlash to the initiative, president Obama’s administration has gone forward with allocating stimulus money towards constructing the smart grid. One of the historic first steps has been taken as the city of Miami proposes leading the initiative with a $200 million project to create a smart grid within Florida. The smart grid will be built by network powerhouses Cisco Systems and General Electric, among several other companies wanting to get their feet wet with the new wave of green smart technologies.

read the full article